Maytag rinse and spin cycle - Spinning — a fun name for indoor cycling workouts that people do both at home and at local gyms — has become an increasingly popular form of exercise over the last few years. Wheth...

 
Rinse and Spin Cycle. The Rinse and Spin cycle works by combining a rinse and high spinning speed. You can use the cycle independently or combine it with a load that requires an extra rinse. It is perfect for items that need rinsing without the use of detergent. E.g. swimwear. It uses cold water temperature for action.. Tennessee baseball walk up songs

Maytag Bravos XL washer, model no. MVWB835DW2, will not complete a wash cycle. Tub fills, wash starts, then after a few minutes, the power light starts blinking and the tub starts draining.5. Washer Won’t Spin Fast Enough. Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch. Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch. 6. Maytag washing machine cycle times differs depending on the cycle. For most Maytag washers, the shortest is the Quick Wash Cycle (takes about 15-40 minutes to clean clothes) while the longest is the Whites Cycle (it can take up to 2 hours and 50 minutes to get white clothes clean) PS: Always select the recommended cycle for your load for the ... AT&T's high dividend yield won't last. Scenario analysis for T stock implies investors should hold their spin-off shares for long-term gains. The high dividend yield of T stock won...5). The Drain Is Blocked. If the rinse cycle won’t start, the machine is stalling because the drain is blocked. Therefore, the dirty water cannot escape the unit. Blocked drains are tricky because the device won’t open until the cycle ends. If the cycle keeps repeating, you cannot open the lid to check the drain.Common reasons for a Maytag Front Load washer not draining, spinning, or leaving wet loads at the end of the cycle: Delicate or handwash cycle selected. Extra Low, Low or No Spin option selected. Washing one bulky item. Excessive suds. Drain hose kinked or drain clogged. Drain hose more than 96” above the floor.Hence, this cycle provides a heavy-duty wash. Whites. The whites cycle is similar to the heavy cycle, except it targets heavily soiled white clothing or fabrics. Delicate . The delicate cycle is the gentle wash mode and is best for clothes prone to damage, such as blouses, soft fabrics, or lingerie. Quick wash . The quick wash cycle will get ...Rinse and spin is a cycle used for loads requiring an additional rinse cycle or to complete a load after a power interruption. On some models, you may have to select the "Drain and Spin" Cycle, then select "Extra Rinse". Check your …Heat the vinegar in the microwave until it is very hot but not boiling. Dip an old toothbrush into the heated vinegar and give the dispenser a good scrubbing. It is also helpful after the scrubbing to fill the dispenser with the warm distilled white vinegar and let the empty washer run through a hot wash cycle.2. Unbalanced load or overfilled washer. If the washer is unbalanced or overfilled, it may struggle to spin and cause the clothes to still be wet after the spin cycle. Removing some items from the washer or balancing the load in the tub should resolve this issue. Make sure you don’t overfill the washer and that the load is balanced to avoid ...The washer is a Maytag LAT9706AAE and is at least eight years old (I bought it with the house) but has been reliable until this. The load size was set between medium and large (it's on a continuous slider); Extra Rinse (which uses more water in the rinse cycle) was turned off and Extra Spin (which causes it to spin for longer) was turned on.Wash two or three in attempt to balance the load for spin. Make sure that the top of the impeller is visible. Use towels as counterweight if needed to ensure the load does not go off balance. Never overload the washer. Clothes should be loosely added and only as high as the top row of holes in the wash basket. Wash like items together; separate ...This is as quick summery of the Maytag Centennial washer's automatic diagnostic test and what lights are lit for each step. Note: you can advance each step manually by pressing the "start" button. Centennial washer lid should lock ="done" + "lock". Centennial washer cold valve should open ="spin" + "lock". Centennial washer hot valve should ...6. Worn Motor Coupling. The motor coupling, whose primary job is to connect the washer’s motor and its transmission, plays a vital role in its spinning. The washer won’t spin even though it may drain if it’s old. Often, the motor coupling wears down from washer overloading, but it can happen naturally over time. Fix. Drain and Spin Operation. In general, Top-Load and Front-Load Washers with only a Rinse & Spin cycle can still achieve a Drain and Spin without the rinse by selecting the Rinse & Spin cycle, and then de-selecting the Deep Rinse (Top-Load) or Extra Rinse (Front-Load) option. Drain & Spin, on most models, will add water for a couple of seconds ... The stress response cycle is your body's response to an external stress trigger. It's broken down into three stages: alarm, resistance, and exhaustion. Here's what happens in each ... High Use this cycle to eliminate 99.9% of bacteria when used in conjunction with the Oxi option. Preset cycle settings must be used to achieve the proper sanitization. Be sure to add an Oxi product to the Oxi dispenser. Swimsuits and items requiring rinsing without detergent Rinse & Spin Cold Rinse Only High Combines a rinse and spin for loads ... Washer makes a clicking/clacking type noise. Typically, a clicking or clacking noise will only occur at the start of a cycle. Most likely, it is the sound of the lid locking. CLICK HERE for more information on the lid locking.1. Water Supply Issues. One of the most common reasons for a washer to stop during the rinse cycle is inadequate water supply. Ensure that both the hot and cold water faucets connected to your machine are fully open. Check for kinks or obstructions in the hoses, as these can impede the water flow.Delay the start of the wash cycle to take loads straight from soaking to washing without coming back to the washer. Quick Wash Cycle. The quick wash cycle cleans small, lightly soiled loads in 30 minutes with extra high spin speeds, pairing nicely with the quick dry cycle on matching Maytag® dryers to get your clothes ready in no time.The default cycle will only drain and spin. This cycle can also be used to refresh a load by adding the Extra Rinse option, the cycle will rinse, drain, and spin. Use this cycle with …Washer Stops Mid-Spin: A spin cycle that stops prematurely could be a symptom of a failing lid switch, a malfunctioning timer, or issues with the washer’s water level control. Causes of Spin Cycle Problems in Maytag Washers 1. Washer Not Spinning Problem Description and Symptoms:Common reasons for a Maytag Front Load washer not draining, spinning, or leaving wet loads at the end of the cycle: Delicate or handwash cycle selected. Extra Low, Low or No Spin option selected. Washing one bulky item. Excessive suds. Drain hose kinked or drain clogged. Drain hose more than 96” above the floor.Delay the start of the wash cycle to take loads straight from soaking to washing without coming back to the washer. Quick Wash Cycle. The quick wash cycle cleans small, lightly soiled loads in 30 minutes with extra high spin speeds, pairing nicely with the quick dry cycle on matching Maytag® dryers to get your clothes ready in no time.Loud and unpleasant noises produced while washing is one such problem. Maytag washers may make loud noises when there is a defect in the tub bearing or motor coupling, a worn-out drive pulley, damaged clutch assembly, or a clogged drain pump. Additionally, washers often make a squealing or whining noise when they’ve been …Rinse & Spin* Tap Cold Heavy + Extra Rinse Medium + Extra Rinse ON OFF Max High Medium Auto 28 *NOTE: Must select Drain & Spin cycle and Extra Rinse option. …To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the load in the basket. If Low Spin or No Spin was selected, the washer might not remove enough water from the load. Refer videos shown below for “Leveling the washer” or “Out of Balance”. Leveling the Washer. To get the washer in Stand-By mode, plug washer in. Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence. Follow Test Mode Procedure: Electric scooter startup Spin was long considered to be a bit of an underdog in the micromobility space. Before selling to Ford, Spin had raised just $8 million, while competitors ...Use the recommended cycle/speed spin for your garment. To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the weight in the basket. If Low Spin or No Spin was selected, the washer might not remove enough water from the load.To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the load in the basket. If Low Spin or No Spin was selected, the washer might not remove enough water from the load. Refer videos shown below for “Leveling the washer” or “Out of Balance”. Leveling the Washer.Review the selected cycle settings and make sure you’ve chosen the appropriate cycle for your load. 21. Excessive Suds in the Washer. Description: The Maytag MVW7230HW produces an excessive amount of suds during the wash cycle, leading to poor cleaning results. Cause: Excess suds can occur due to using non-HE …May 20, 2022 ... ... cycle on intermittent spin before I decide to record before the final rinse and spin cycle. I showed that as an action. ©Ryan's Washer VideosSep 7, 2023 · 6. Damaged drive belt. (Image credit: Shutterstock) The drive belt is what rotates the drum in your washing machine. So, if it’s stopped spinning, there could be a problem here, too. You can ... During a rinse and spin cycle, sometimes no form of detergent is used as it isn’t used as a form of deep cleaning. It rinses the clothing with clean water and then spins at a fast speed to remove any moisture from the load. The difference between Drain and Spin and Rinse and Spin is that drain and spin will remove all the excess water from ...The default cycle will only drain and spin. This cycle can also be used to refresh a load by adding the Extra Rinse option, the cycle will rinse, drain, and spin. Use this cycle with …Below are the 13 probable causes why your Maytag Bravos washer won’t spin: 1. Power Problem. Sometimes, your washer won’t spin the clothes if the washer doesn’t even start. One reason why it won’t start is due to a lack of power. Start by confirming if your washer is plugged into the wall socket and if it’s on.Step 3: Spinning. Once the rinse stage is finished, a dedicated spin cycle is used to drain excess water from your laundry. In this sense, a washing machine’s rinse function is part of any wash cycle you may use. With many washing machines, it’s even possible to adjust the desired number of rinse cycles. To stop the spin dry cycle of the Maytag MVW5430MW washing machine and reposition clothes to eliminate wobbling, follow these steps: 1. Press the Start button to start the cycle. 2. If the cycle needs to be interrupted, press the Power/Cancel button (or press and hold the Start/Pause button for three seconds if there is no Power/Cancel button). 3. The Drip Cap. In theory, when your Maytag washer reaches its spin cycle, it should begin spinning. Add a few extra pieces of clothing to the load if you have only one or two small items -- like socks or T-shirts -- in the washer. The washer includes a "Sud" function that clears the suds from the appliance, but this phase forces the spin cycle ...Rinse away loose soils as clothes go in or fill the tub for a soak before the cycle begins. OPTIMAL DOSE DISPENSER Adds the right amount of detergent for up to 8 loads in a …The washer will not rinse well or spin correctly if tightly packed. Not all settings are available with each cycle, and some options cannot be used together. Not all options …May 2, 2022 ... ... Maytag Performa or Advanta washer won't spin. Click here to order a new ... Maytag centennial washer won't rinse or spin. Hameed Appliances ...The washer will not rinse well or spin correctly if tightly packed. Not all settings are available with each cycle, and some options cannot be used together. Not all options …Maytag Washer Stuck on Rinse. If your Maytag washer is stuck on rinse, a common cause can be a clogged drain hose or pump, preventing water from efficiently draining out. Check the drain hose for kinks or obstructions, and inspect the pump for any debris. Cleaning and ensuring a clear pathway can often resolve the rinse cycle issue.1. Level the Washer. If your Maytag washing machine makes a loud noise during the spin cycle, it may be due to an unbalanced load. To fix this, you’ll need to ensure the washer is level. You can quickly adjust the legs at the washer’s bottom. First, unplug the washer and use a bubble level to check the washer’s level.Using extra high-spin speeds, the Quick Wash cycle cleans small, lightly soiled loads in 15 minutes.* Get clean clothes fast by pairing it with the Quick Dry cycle on matching Maytag® dryers. *Based on a 3-lb load. Steam Option. Steam permeates deep into fibers for potent cleaning action. Combine with the Extra Power button or use on select ...Maytag Bravos XL washer, model no. MVWB835DW2, will not complete a wash cycle. Tub fills, wash starts, then after a few minutes, the power light starts blinking and the tub starts draining. ... I believe it is Temperature, spin speed, soil level(?). To do that: With the unit off, start with the top button and press and release each in ... Extra Rinse Fresh Hold®/ Fresh Spin™ Extra Power This cycle combines low-speed tumbling and medium-speed spin for gentle fabric care and reduced wrinkling. Clothing, bedding, and towels requiring sanitization Sanitize Hot Off Slow Medium Medium Fast Fast Steam** Extra Rinse Fresh Hold®/ Fresh Spin™ Extra Power This cycle eliminates 99.99% ... Broken Drive Pulley: A Possible Culprit. A broken drive pulley can be a source of loud noise during spin cycles in your Maytag washer. The drive pulley is responsible for connecting …Common problems with Maytag Bravos washers include failure to start, water filling slowly, water leakage, failure of the door or lid to lock and overflowing. Other problems include...To check the valve, first disconnect the power supply to your washer. Then locate the inlet valve at the back of the washer and turn off the water supply. Next, take a look at the screens in the valve. If they’re dirty or clogged with debris, use a screwdriver to remove the debris and clean them off.1. Be sure the washer is in standby mode (plugged in with all indicators off). Press and hold the start/cancel button for 3 seconds to turn everything off. 2. Perform the following sequence of movement using the cycle selector knob. NOTE: AFTER RESET, sequence “a” through “e” must be completed within 6 seconds.Top load maytag washing machine goes thru the 1st wash cycle and drains ok. Gets to the rinse cycle and fills up and starts to agitate only. I did replace the lid switch and still the same problem. The timer actually advances past the "spin" all the way to the end never draining the 2nd fill.Jan 29, 2024 · The cycle combines high-speed wash action and high-speed spin, making it harsher on clothes. Heavy Duty: Select this washer setting for towels and sturdy fabrics like jeans. It is also appropriate for heavily soiled items. The cycle offers a longer wash cycle with high-speed agitation and a high-speed spin to remove as much moisture as possible. The washer is a Maytag LAT9706AAE and is at least eight years old (I bought it with the house) but has been reliable until this. The load size was set between medium and large (it's on a continuous slider); Extra Rinse (which uses more water in the rinse cycle) was turned off and Extra Spin (which causes it to spin for longer) was turned on.Keith goes over the different Washer Spin cycles and speeds in Maytag, whirlpool and GE washers. Appliance Factory and Mattress Kingdom is the nation’s 28th ...May 4, 2021 · Test the Door Latch. The door latch makes sure the door on your Maytag washer stays closed when it is operating. When it opens, the washer won’t spin. To check the door latch: Check your manual to find out if you have a mechanical door latch or an electronic one. Make sure the power is switched off. Maytag Washer Stuck on Rinse. If your Maytag washer is stuck on rinse, a common cause can be a clogged drain hose or pump, preventing water from efficiently draining out. Check the drain hose for kinks or obstructions, and inspect the pump for any debris. Cleaning and ensuring a clear pathway can often resolve the rinse cycle issue.Is your washer not spinning as it should? It can be frustrating when your washing machine doesn’t perform its intended functions properly. One of the most common issues homeowners ...I'm looking up answers on my Whirlpool W10304136 My washing machine runs until the spin cycle and it seems to have weird locking/unlocking issues. ... It consistently had a 45 sec. rinse cycle on a normal wash. The 2nd rinse was 4 min. Maytag's service rep said they did not have any t ...Using extra high-spin speeds, the Quick Wash cycle cleans small, lightly soiled loads in 30 minutes.Get clean clothes fast by pairing it with the Quick Dry cycle on matching Maytag® dryers. Power™ agitator. Trust the Power™ agitator to knock the stubborn out of stains. A 360-degree wash action keeps clothes moving to help break up messes. Common reasons for a Maytag Front Load washer not draining, spinning, or leaving wet loads at the end of the cycle: Delicate or handwash cycle selected. Extra Low, Low or No Spin option selected. Washing one bulky item. Excessive suds. Drain hose kinked or drain clogged. Drain hose more than 96” above the floor. A broken drive pulley can be a source of loud noise during spin cycles in your Maytag washer. The drive pulley is responsible for connecting the motor to the washer drum, so if it’s damaged or broken, it can result in a noisy spin cycle. To diagnose this problem, take a close look at the pulley and inspect it for any signs of damage or looseness.United States: Canada: 1–800–344–1274 1–800–688–2002 Maytag Brand Appliances Maytag Brand Appliances Customer eXperience Center Customer eXperience Centre. Step 5. Press Start/Pause. 553 Benson Road 200–6750 Century Ave. Benton Harbor, MI 49022–2692 Mississauga, Ontario L5N 0B7.STEP 2: CHECK THE LAUNDRY LOAD. An overfilled wash basket may be the cause of a shaking washer. Try removing some items and evenly dispersing the remaining load. Washing one large, bulky item or something very absorbent like a comforter can also throw the washer off balance. Add other items to equalize the weight and stop the washer from …Balance the Load. Oversized items, Water Resistant Materials, or a large, unevenly distributed load can cause water to splash off the top of the load or washer basket. Evenly distribute the load in the washer basket; items should not be higher than the top row of holes on the basket. Be careful not to cover the middle of the impeller.This video shows you how to Diagnose and Repair a *SAV4655AWW Maytag Washer W10116791 Triple Lip Assembly**Symptoms may include:* Leaking Water During Spin C...Inside the pump is an impeller that continually spins whenever the pump is on. When the impeller spins, it will pull water in from one end of the pump (coming from the washer drum) and drive it out through another (out through the drain hose). Related: 5 Reasons Why GE Dishwasher Not Draining Typically, you will notice the drain pump …Whirlpool Stock Is in a Bullish Spin Cycle Into Earnings...WHR Investors will hear Monday from Whirlpool Corp. (WHR) , which is scheduled to announce its second-quarter earnings re...5. Washer Won’t Spin Fast Enough. Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch. Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch. 6.Aug 15, 2018 ... MVWX655DW Maytag Deep Water Wash Cycle, Extra-Heavy Soil level, Extra-Rinse, 5-Jeans · MVWB835DW MAYTAG, Normal Cycle, Extra Rinse Off, Spin ...The washer may be overloaded. When the washer is overloaded, the balance system may be under pressure. This could cause different types of noises, such as squeaks or squeals. Always follow the loading instructions in your Owner's Manual. Refer videos shown below for “Leveling the washer” or “Out of Balance”. Leveling the Washer.To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the load in the basket. If Low Spin or No Spin was selected, the washer might not remove enough water from the load. Refer videos shown below for “Leveling the washer” or “Out of Balance”. Leveling the Washer. Top load maytag washing machine goes thru the 1st wash cycle and drains ok. Gets to the rinse cycle and fills up and starts to agitate only. I did replace the lid switch and still the same problem. The timer actually advances past the "spin" all the way to the end never draining the 2nd fill. Have you found yourself in a situation where your washer won't spin? Its probably the most common washer-killing problem you'll find yourself in. In this vid...Rinse & Spin (15 – 20 Minutes) The Rinse & Spin cycle is the quickest cycle on a Maytag washing machine averaging 15 – 20 minutes. This cycle is ideally best for items requiring rinsing without using detergent, such as swimsuits. While water temperature may vary, the cycle works best with Tap Cold water and a high-speed spin or rinse setting.2. Unbalanced load or overfilled washer. If the washer is unbalanced or overfilled, it may struggle to spin and cause the clothes to still be wet after the spin cycle. Removing some items from the washer or balancing the load in the tub should resolve this issue. Make sure you don’t overfill the washer and that the load is balanced to avoid ...The washer will not rinse well or spin correctly if tightly packed. Not all settings are available with each cycle, and some options cannot be used together. Not all options …Maytag washers may make loud noises when there is a defect in the tub bearing or motor coupling, a worn-out drive pulley, damaged clutch assembly, or a clogged drain pump. Additionally, washers often make a squealing or whining noise when they’ve been overloaded. If your washer has been making any of the noises described above, you’ve come ...Aug 15, 2023 · 1. Load Imbalance: Overloading the washing machine or having an uneven distribution of clothes in the drum can lead to an imbalance. This imbalance can trigger safety mechanisms that prevent the machine from spinning. Try redistributing the load more evenly and ensuring the clothes are not clumped together. 2. Step 3: Spinning. Once the rinse stage is finished, a dedicated spin cycle is used to drain excess water from your laundry. In this sense, a washing machine’s rinse function is part of any wash cycle you may use. With many washing machines, it’s even possible to adjust the desired number of rinse cycles.We bought this Maytag washer a couple years ago model (MVWC465HW2) and we have had nothing but issues with it, but it goes through the wash cycle but when it gets to rinse it seems to get stuck and the rinse light starts flashing and will continue flashing forever until we home the button down to cancel the cycle, but then the lid stays locked for several …May 4, 2021 · Test the Door Latch. The door latch makes sure the door on your Maytag washer stays closed when it is operating. When it opens, the washer won’t spin. To check the door latch: Check your manual to find out if you have a mechanical door latch or an electronic one. Make sure the power is switched off.

Agitation/Wash. There will be a knocking/thumping noise as the drive system shifts from agitation mode to spin mode or vise versa. These sounds are part of the normal washer operation. Do not overload the machine, and do not wash 1 item by itself. If you wash a bulky item, such as a blanket, use towels as counterweight to even the load.. East hills wine and spirits

maytag rinse and spin cycle

Step 3: Spinning. Once the rinse stage is finished, a dedicated spin cycle is used to drain excess water from your laundry. In this sense, a washing machine’s rinse function is part of any wash cycle you may use. With many washing machines, it’s even possible to adjust the desired number of rinse cycles.Manually advance the timer to “Rinse” and see whether or not the wash cycle resumes. Contact a washing machine repair specialist to inspect the timer. Bad Locking Tab and Lid Switch (top-loading) Even though a washing machine will start if the tab and switch break, the washer won’t rinse or spin unless the tab and switch unite.Maytag washers may make loud noises when there is a defect in the tub bearing or motor coupling, a worn-out drive pulley, damaged clutch assembly, or a clogged drain pump. Additionally, washers often make a squealing or whining noise when they’ve been overloaded. If your washer has been making any of the noises described above, you’ve come ...Jan 22, 2024 ... ... cycle this time. Try my favorite detergents ... What's interesting about this one is the cool down and wash spin are high speed while the final ...Run spin cycle. Test with a spin to check noise levels have lowered with the new snubber pad installed. Repeat for all pads. Replace any other worn pads found on vertical or horizontal tub surfaces. Reconnect power. Machine repairs are complete and unit can now be safely plugged back in. View Maytag Washing Machine Snubber Pad partsSince it will spin when you manually move the dial this suggests there is nothing mechanically wrong with the machine. Try changing out the timer and see if that fixes things. You can post new topics in this forum. You can reply to topics in this forum. You can delete your posts in this forum.Jan 4, 2023 · Time: 15 – 25 minutes. The following are steps to fix the spin light blinking problem in the Maytag washer: If the reset doesn’t work, unplug your washing machine. Open the drain filter cap and look if it is clogged or not, you can find it in the front bottom right side. Remove all the dirt from the filter and make it clean. To check the valve, first disconnect the power supply to your washer. Then locate the inlet valve at the back of the washer and turn off the water supply. Next, take a look at the screens in the valve. If they’re dirty or clogged with debris, use a screwdriver to remove the debris and clean them off.Have you found yourself in a situation where your washer won't spin? Its probably the most common washer-killing problem you'll find yourself in. In this vid...This short wash cycle has an extrahigh-speed spin followed by intermittent tumbling and fan activation to circulate air through the clothes. Use Drain & Spin to remove excess water from the load. Spin speed can be set to a lower setting. Use this cycle every 30 washes to keep the inside of your washer fresh and clean.06 - Maytag Washing Machine Door Lock Motor and Switch Assembly. The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle.Recommended fix: Maytag washer stuck on spin. How to reset your Maytag washer. #1- Malfunctioning timer (Timer is not advancing so Spin cycle is not working properly) #2- Bad lid switch assembly. #3- Defective motor coupling – most likely cause if your Maytag washer agitates but won’t spin. #4- Damaged drive belt.Adjust the drain pipe height to 30-96 inches to boost the drain pump’s pumping action. 5. Poor Drainage. Unkink and unclog the drain hose and clean the drain filter and drain pump if they are dirty. 6. Unbalanced Load. Balance your clothes in …Rinse & Spin* Tap Cold Heavy + Extra Rinse Medium + Extra Rinse ON OFF Max High Medium Auto 28 *NOTE: Must select Drain & Spin cycle and Extra Rinse option. …Rinse & Spin* Tap Cold Heavy + Extra Rinse Medium + Extra Rinse ON OFF Max High Medium Auto 28 *NOTE: Must select Drain & Spin cycle and Extra Rinse option. ….

Popular Topics